Avaliar o efeito da termociclagem (TC) na resistencia de uniao a microtracao (μTBS) de dois agentes cimentantes a uma ceramica feldspatica e mensurar a espessura da pelicula (FT) desses agentes cimentantes. Para o ensaio de μTBS, dezesseis blocos (6,4 x 6,4 x 4,8 mm) foram fabricados utilizando uma ceramica feldspatica, condicionados com acido fluoridrico 10%, lavados, secos e aplicado o agente silano na superficie.Os blocos ceramicos foram divididos em dois grupos (n=8): Gr1: cimento resinoso de polimerizacao dual e Gr2: resina flow. Os dois agentes cimentantes foram entao aplicados sobre as superficies tratadas. Os palitos (1 ± 0.1mm²) foram confeccionados e divididos de acordo com duas condicoes de armazenagem: seco, as amostras foram imediatamente submetidas ao teste de μTBS, e TC (6.000 ciclos; 5°C-55°C). The μTBS was evaluated using a universal testing machine (1 mm/min). Os dados de μTBS (MPa) foram submetidos a Analise de Variancia (ANOVA) dois fatores e ao teste de Tukey (5%). Para o teste FT (ISO 4049), 0,05 ml de cada agente cimentante (n=8) foi prensado entre duas placas de vcidro (Mylar) (15kg) durante 180 segundos, fotopolimerizadas e a FT foi mensurada utilizando um paquimetro digital (Modelo 727-2001). Os dados (mm) foram submetidos a Analise de Variancia (ANOVA) um fator. O agente cimentante nao influenciou os resultados de resistencia de uniao a microtracao (p=0,4467). Os maiores valores de resistencia de uniao for a encontrados apos a TC (20,5±8,6 MPa) comparado com a condicao sem TC (13,9±4,7 MPa), para ambos os agentes cimentantes. Os agentes cimentantes apresentaram espessuras de pelicula similares: Gr1- 0,052±0,016 mm; Gr2- 0,041±0,003 mm). Os agentes cimentantes apresentaram espessura de pelicula e valores de μTBS, em condicao com e sem TC, e que a TC aumentou a resistencia de uniao, independente do agente cimentante utilizado.
The aim of the present study was to evaluate the effect of thermocycling (TC) on the microtensile bond strength (μTBS) of two luting agents to feldspathic ceramic and to measure their film thickness (FT). For the μTBS test, sixteen blocks (6.4 x 6.4 x 4.8 mm) were fabricated using a feldspathic ceramic, etched with 10% hydrofluoric acid, rinsed and treated with the silane agent. The ceramic blocks were divided into two groups (n= 8): Gr1: dual-cured resin cement and Gr2: flowable resin. The luting agents were applied on the treated surfaces. Microsticks (1 ± 0.1mm²) were prepared and stored under two conditions: dry, specimens immediately submitted to the μTBS test, and TC (6,000 cycles; 5°C-55°C). The μTBS was evaluated using a universal testing machine (1 mm/min). The μTBS data (MPa) were submitted to two-way ANOVA and Tukey’s test (5%). For the FT test (ISO 4049), 0.05 ml of each luting agent (n=8) was pressed between two Mylar-covered glass plates (150 N) for 180 seconds and light polymerized. FT was measured using a digital paquimeter (Model 727-2001). The data (mm) were submitted to one-way ANOVA. The luting cement did not influence the μTBS results (p=0.4467). Higher microtensile bond values were found after TC (20.5 ± 8.6 MPa) compared to the dry condition (13.9 ± 4.7 MPa), for both luting agents. The luting agents presented similar film thicknesses: Gr1- 0.052 ± 0.016 mm; Gr2- 0.041 ± 0.003 mm. The luting agents presented similar film thickness and μTBS values, in dry and TC conditions and TC increased the bond strength regardless of the luting agent.